We have discovered this article pertaining to How to Install a Bathtub Yourself below on the web and believe it made good sense to talk about it with you in this article.
Mounting a bath tub isn't specifically brain surgery, yet it does require solid plumbing, carpentry, as well as in some cases, tiling abilities. Replacing an old tub with a brand-new one is additionally a reasonably hard job. If the old bathtub is easily easily accessible, the task can move quickly; if you need to open up a wall to eliminate the old tub as well as place the brand-new bath tub, the job is much harder. In either instance, the job is within a house handyman's skills, although you will need a helper to move out the old bathtub and also set in the new one. See to it you have qualified yourself for the work and also fit trying it. Rather than employing a contractor to take control of a halfway-completed task, it is far better to take into consideration utilizing one prior to you begin. Possibilities are you may require an expert plumber to make tube connections.
This short article will assist you mount a brand-new bath tub in your restroom if you have already bought a brand-new bathtub and don't require to transform the plan of your previous water supply pipes.
Your tools and material list must make up the following:
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installment, then the first thing you ought to do is disconnect the water. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The procedure of getting rid of the existing faucets can be quite problematic as a result of the restricted gain access to that is usually the case.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a towel all set for the continuing to be water that will originate from the pipelines. Once the supply pipes have been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleaned up of any kind of old securing substance.
Before moving on to fit the brand-new taps, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end provides a connection to the current supply pipes.
If you require to fit a monobloc, then you will require decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the placing hole in the bath/basin ensuring that the washers are in place between the faucet and the sink. Protect the tap in position with the producer given backnut. When the tap is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The previous kind ought to be attached to the faucet finishes first, tightening up only by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Using the two wood boards under its feet, position the bathtub in the required position. The wood boards are valuable in uniformly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 small points.
The following goal is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bathtub up until the level checks out level.
To set up taps, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipeline by making a compression join; after that do the same for the various other tap.
Switch on the supply of water and also inspect all joints as well as brand-new pipework for leaks and tighten them if needed. Load the bath tub as well as also examine the overflow electrical outlet and also the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as defined in the supplier's instruction manual. Tiling and securing around the bath tub needs to wait until the tub has actually been made use of at least once as this will certainly resolve it right into its last position.
Getting ready for the Setup
To start with, the sustaining structure provided with the bathroom needs to be fitted (if required) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets device to avoid pressure on the tub.
Fit the flexible faucet ports to the bottom of both faucets utilizing 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. See to it you make use of every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last position.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to break a rigid seal, triggering the water to penetrate the wall in between the bath and the tiling, causing difficulties with moisture and also possible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your components and fittings. They are marketed in tubes as well as cartridges, and also are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly fill the bath tub with water before securing, to permit the movement experienced when the bathtub is in use. The sealer can split fairly very early if you do not take into account this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally quickly available on the market. It is suggested to fit the tiles using waterproof or water-proof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been shown that editorial on Installing A Bathtub from a friend on our other website. Sharing is nice. Helping people is fun. I take joy in reading our article about How to Install a Bathtub Yourself.
Drain issues? Reach out!